How To Fix Leaky Bathtub Faucet Single Handle

July 9, 2025
how to fix leaky bathtub faucet single handle

Written by: Deane Biermeier / Facts Checked by; Ryan Cullenward / Products Tested by Licensed Interior Designers

  • Home
  • /
  • Blog
  • /
  • How To Fix Leaky Bathtub Faucet Single Handle

A leaky bathtub faucet with a single handle not only wastes water but also drives up your utility bills and can cause long-term damage to your bathroom fixtures. This comprehensive guide will walk you through everything you need to know to diagnose, fix, and prevent a leak in your single-handle bathtub faucet quickly, efficiently, and without the need for a plumber.

Tools and Materials Needed

Before we dive into the repair process, ensure you have the following tools and replacement parts on hand:

Adjustable wrench

Phillips and flathead screwdrivers

Allen wrench (if needed)

Faucet cartridge (specific to your faucet model)

Replacement O-rings and washers

Needle-nose pliers

Silicone grease

Towel or rag

Plumber’s tape

Step 1: Shut Off the Water Supply

Start by turning off the water supply to your bathtub. Most bathtubs don’t have a local shut-off valve, so you may need to turn off the water at the main valve.

Locate your home's main water supply shutoff.

Turn the valve clockwise to stop the water flow.

Open the bathtub faucet to release any remaining water and pressure.

Step 2: Plug the Drain

Use a bathtub stopper or a rag to plug the drain. This prevents any small screws or parts from falling into the drain while you work.

Step 3: Remove the Faucet Handle

The single handle faucet can vary slightly by manufacturer, but most will follow these general removal steps:

1. Look for a set screw at the base or under the decorative cap of the handle.

2. Use an Allen wrench or screwdriver to loosen the screw.

3. Gently wiggle and pull the handle off the faucet assembly.

4. If stuck, apply a little penetrating oil and let it sit for a few minutes.

Step 4: Inspect and Remove the Escutcheon Plate

After the handle is removed, you’ll see the escutcheon plate (decorative trim) and possibly a sleeve.

Unscrew or slide off the escutcheon plate.

Use a wrench to remove any mounting nuts or screws securing the cartridge or valve stem.

Step 5: Extract the Cartridge or Valve Stem

This is the core part of the repair and the most likely source of the leak. Depending on the faucet brand, the internal component might be a cartridge or a compression valve.

1. Use pliers to pull the cartridge or valve stem straight out.

2. Take care not to damage the surrounding parts.

3. Inspect the old cartridge for cracks, mineral buildup, or worn O-rings.

Pro Tip: Take the old cartridge to your local hardware store to match the exact model. Universal cartridges don’t always fit properly.

Step 6: Replace O-Rings and Washers

Even if the cartridge itself is still in good condition, the O-rings and rubber washers can wear out and cause leaks.

Use needle-nose pliers to remove the old O-rings and washers.

Apply a light coating of plumber’s silicone grease to the new O-rings.

Install the new O-rings and washers in the exact orientation.

Step 7: Install the New Cartridge or Valve Stem

Now it’s time to install the new or repaired component:

1. Align the cartridge properly based on the faucet model.

2. Push the new cartridge into place until it is seated firmly.

3. Reinstall the retaining nut or clip that secures it.

4. Replace the escutcheon plate and screw it back into place.

Step 8: Reattach the Handle

Slide the faucet handle back onto the stem.

Tighten the set screw with your Allen wrench.

Replace any decorative caps that were removed.

Step 9: Turn Water Supply Back On and Test

Slowly turn the main water supply back on.

Open the faucet and check for leaks.

Turn the handle to both hot and cold settings to ensure full functionality.

If the faucet no longer drips when turned off, the repair was successful.

Common Causes of a Leaky Bathtub Faucet Single Handle

Understanding the root cause of the leak can help prevent future issues:

Worn-out cartridge: The most frequent cause.

Damaged O-rings: These create a seal; when they wear out, leaks occur.

Corrosion or sediment buildup: Can damage internal seals and cause dripping.

Improper installation: If the handle or cartridge is misaligned, it may not shut off fully.

Preventive Maintenance Tips

To avoid leaks in the future, follow these maintenance practices:

Inspect and clean your faucet once every 6 months.

Replace O-rings annually if your water has high mineral content.

Use a water softener to reduce mineral buildup.

Never force the faucet handle; excessive torque can damage the internal parts.

When to Call a Professional

If your faucet continues leaking after replacing the cartridge and O-rings, the problem could be deeper:

Damaged plumbing inside the wall

Corroded valve body

Poor water pressure affecting operation

In such cases, it's best to consult a licensed plumber for further diagnosis.

Conclusion

Fixing a leaky single-handle bathtub faucet is a manageable DIY project that can save you water, money, and frustration. With the right tools, clear steps, and a bit of patience, you can restore your faucet’s performance in less than an hour.

Disclosure: Sanitarysupply.org receives an affiliate commission on some, but not all, of the products we recommend—but only if you decide to click through to the retailer's site and make a purchase.


You may also like

How To Clean Bathtub Jets
How To Remove Bathtub Drain Plug
Leave a Reply

Your email address will not be published. Required fields are marked

{"email":"Email address invalid","url":"Website address invalid","required":"Required field missing"}

Never miss a good story!

Subscribe to our weekly newsletter to keep up with the latest trends!