When your bathtub drains slowly or not at all, the first suspect is often the bathtub drain plug. Over time, plugs become clogged, worn out, or simply stuck. Removing and cleaning or replacing the bathtub drain plug is essential maintenance. Here, we provide a comprehensive guide to remove all types of bathtub drain stoppers, with precise, clear instructions that anyone can follow.
Tools You May Need to Remove a Bathtub Drain Plug
Before diving in, gather the following tools:
Screwdriver (Flathead and Phillips)
Pliers or adjustable wrench
Drain key or smart dumbbell wrench (for some drain types)
Needle-nose pliers
Allen wrench (hex key)
Lubricating spray (WD-40)
Clean cloth or rag
Identify Your Bathtub Drain Stopper Type
There are multiple types of bathtub drain stoppers, and removal methods depend heavily on the design. Below are the most common types:
1. Lift-and-Turn Stopper
2. Push-Pull Stopper
3. Toe-Touch Stopper
4. Trip Lever Stopper
5. Flip-It Stopper
6. Pop-Up Stopper
7. Grid or Screen Drain Cover
Each requires a slightly different removal process, which we outline in full detail below.
How to Remove a Lift-and-Turn Bathtub Drain Plug
Lift-and-turn stoppers are identified by their ability to be turned to open or close.
Steps:
1. Open the stopper by turning it to the open position (usually counterclockwise).
2. Hold the stopper body and unscrew the knob on top. If it's tight, use pliers wrapped in a cloth to avoid scratching.
3. Once the top cap is removed, unscrew the post beneath it using a flathead screwdriver.
4. Pull the entire unit out from the drain.
Pro Tip: If it spins without coming loose, check for a set screw on the shaft just under the cap—loosen it with an Allen wrench.
How to Remove a Push-Pull Bathtub Drain Plug
Push-pull stoppers open and close with a simple press.
Steps:
1. Pull the stopper into the open position.
2. Grip the knob tightly and unscrew it counterclockwise.
3. Use a screwdriver to remove the mounting post beneath the cap.
4. Once loosened, simply lift the stopper out.
How to Remove a Toe-Touch Drain Stopper
This is spring-loaded and opens with a press from the toe.
Steps:
1. Press the stopper down to open it.
2. Hold the base steady while unscrewing the top cap counterclockwise.
3. With the cap removed, unscrew the cylinder post beneath using a screwdriver.
4. Lift out the stopper assembly to access the drain.
How to Remove a Trip Lever Drain Stopper
This is more complex, with a lever on the overflow plate.
Steps:
1. Unscrew the overflow faceplate using a Phillips screwdriver.
2. Gently pull out the entire linkage assembly, which includes rods and the plunger.
3. Be careful not to bend the rods.
4. After removal, clean out the drain pipe and test lever movement before reinstalling.
Note: This type may also control a pop-up stopper at the base or a plunger-style stopper hidden within the pipe.
How to Remove a Flip-It Drain Stopper
These have a toggle switch on top.
Steps:
1. Flip the stopper to the open position.
2. Grip the top and wiggle it back and forth while pulling upward.
3. If tight, use pliers with a cloth to avoid damage.
4. No tools are typically required—it's a friction fit.
How to Remove a Pop-Up Drain Plug
Common in bathroom sinks but also found in tubs.
Steps:
1. Remove the overflow plate if necessary.
2. Use needle-nose pliers to grip and pull up the plug.
3. The mechanism may be attached to a linkage rod; remove carefully.
How to Remove a Grid-Style Drain Cover
These do not act as stoppers but catch hair and debris.
Steps:
1. Use a screwdriver to remove visible screws.
2. If screw less, pry gently around the edges with a flathead screwdriver.
3. Clean the grid thoroughly and reinstall or replace.
Cleaning and Maintenance Tips After Removal
Once the stopper is removed:
Use a drain cleaning brush or wire to remove hair, soap scum, and debris.
Flush the drain with boiling water or a safe enzymatic cleaner.
Lubricate moving parts if reusing the stopper.
Inspect for wear replace old or corroded stoppers.
When to Replace Your Bathtub Drain Plug
If your stopper is:
Rusted or corroded
Doesn’t seal properly
Becomes frequently stuck
Has worn or missing gaskets
It's best to install a new drain stopper. New models are often universal fit and easy to install.
Choosing a New Bathtub Drain Stopper
When shopping for a replacement, consider:
Drain size (standard is 1.5 inches)
Material (brass, stainless steel, plastic)
Style preference (modern, classic, pop-up, etc.)
Ease of maintenance and replacement
Reinstalling or Replacing Your Drain Plug
To reinstall:
1. Insert the cleaned or new stopper into the drain.
2. Screw it in securely but not overly tight.
3. Test for smooth operation and proper sealing.
Tip: Apply plumber’s grease to threads to prevent sticking in the future.
Common Issues with Drain Plugs
Stuck plug: Use WD-40 or vinegar soak to loosen.
Clogs beneath plug: Snake or use a hair removal tool.
Plug spins but doesn’t unscrew: Locate hidden set screws.
Water won’t hold in tub: Gasket or seal likely worn out.
Conclusion
Removing a bathtub drain plug can seem daunting, but with the right knowledge, tools, and method, it’s a straightforward DIY task. Whether you’re troubleshooting a clog, replacing a stopper, or just cleaning, understanding your specific stopper type is crucial.